Pumps
ISO 14224
Equipment — Rotating
ID: equip_PU
| URI: https://www.iso.org/standard/64076.html
No definition available.
Properties / Attributes (51)
| Name | Data Type | Unit / Valid values | Required | Definition |
|---|---|---|---|---|
| Type of driver | — |
Specify | Required | Equipment class, type and identification code |
| Fluid handled | — |
Oil, gas, condensate, freshwater, steam, sea water, crude oil, oily water, flare gas, fuel gas, water/glycol, methanol, nitrogen, chemicals, hydrocarbon-combined, gas/oil, gas/condensate, oil/water, gas/ | Required | Type |
| Fluid corrosive/erosive | — |
cement, other | Optional | a |
| Application – pump | — |
Booster, supply, injection, transfer, lift, dosage, disperse, cooling, drilling, other | Optional | Where applied |
| Pump – design | — |
Axial, radial, composite, diaphragm, | Required | Design characteristic |
| Power – design | — |
Kilowatt | Required | Design/rated power of pump |
| Utilization of capacity | — |
Percent | Required | Normal operating/design capacity |
| Suction pressure – design | — |
Pascal (bar) | Optional | Design pressure |
| Discharge pressure – design | — |
Pascal (bar) | Required | Design pressure |
| Speed | — |
Revolutions per minute or strokes per minute | Optional | Design speed |
| Number of stages | — |
Number | Optional | Centrifugal: number of impellers (in all stages) |
| Body type | — |
Barrel, split case, axial split, cartridge, | Optional | Barrel, split casing, etc. |
| Shaft orientation | — |
Horizontal, vertical | Optional | |
| Shaft sealing | — |
Mechanical, oil seal, dry gas, packed, | Optional | Type |
| Transmission type | — |
gland, dry seal, labyrinth, combined | Optional | Type |
| Coupling | — |
Fixed, flexible, hydraulic, magnetic, | Optional | Coupling |
| Environment | — |
disconnect | Optional | Submerged or dry-mounted |
| Pump cooling | — |
Yes/No | Optional | Specify if separate cooling system is |
| Radial bearing | — |
Antifrictional, journal, magnetic | Optional | Type |
| Thrust bearing | — |
Antifrictional, journal, magnetic | Optional | Type |
| Well identification number | — |
Number or name | Required | Operator description |
| Model type | — |
Onshore well | Required | Type of application |
| ESP Application | — |
Topsides well (dry tree completion) | Required | |
| Fluid corrosiveness | — |
Horizontal pump system (HPS) | Required | Neutral, Sweet, Sour |
| Shaft power rating | — |
Horse power HP | Required | All, where applicable |
| Shaft coupling rating | — |
Horse power HP | Required | All, where applicable |
| Maximum flow capacity | — |
Blpd | Optional | Bolt on discharge head |
| Design performance | — |
Pump curve | Optional | Pump and gas handler |
| Maximum GVF rating | — |
% | Optional | Pump and gas handler |
| Pump stage thrust | — |
Pounds, lbs | Required | Pump and gas handler |
| Housing pressure rating | — |
Psi | Required | Pump and gas handler |
| Maximum flow capacity rating | — |
Blpd | Optional | Bolt on intake |
| Design performance curve | — |
Performance Curve | Optional | Mechanical gas separator |
| Volume contraction capacity | — |
Litres | Required | Seal chamber section |
| Operation deviation limits | — |
Specify [numeric value] | Required | Seal chamber section |
| Thrust load bearing capacity | — |
Pounds, lbs | Required | Seal chamber section |
| Minimum operating speed for thrust bearing | — |
Revolutions per minute, rpm, or Frequency | Optional | Seal chamber section |
| Number and severity of | — |
Specify | Required | Seal chamber section |
| Horsepower requirement | — |
— | Required | |
| Motor performance parameters | — |
Performance curve | Required | Motor |
| Motor voltage for minimum current | — |
Amps | Required | Motor |
| Motor winding temperature rise | — |
Degrees Celsius | Required | Motor |
| Motor operating internal temperature limits | — |
Degrees Celsius | Required | Motor |
| Locked rotor current, | — |
Amps | Required | Motor |
| Voltage rating | — |
Volt | Required | Power cable and MLE |
| Temperature rating | — |
Degrees Celsius | Required | Power cable and MLE |
| Ampacity coefficients | — |
Specify [numeric value] | Required | Power cable and MLE |
| Conductor Size | — |
Millimetres | Required | Power cable and MLE |
| Acceptable minimum | — |
Metres | Required | Power cable and MLE |
| Differential pressure performance | — |
Psi | Required | Pothead |
| Failure modes | 18 failure modes — click to expand
AIR
Abnormal instrument reading
BRD
Breakdown
ELF
External leakage - fuel
ELP
External leakage - process medium
ELU
External leakage - utility medium
ERO
Erratic output
FTS
Failure to start on demand
HIO
High output
INL
Internal leakage
LOO
Low output
NOI
Noise
OHE
Overheating
OTH
Other
PDE
Parameter deviation
PLU
Plugged/ choked
SER
Minor in-service problems
STD
Structural deficiency
UNK
Unknown
|
|||
